12 volt relay wiring diagrams Ansichten: 159

... 12 Volt Relay Wiring Diagrams as well 12 Volt Relay Wiring Diagrams

Amprobe RC-120S Closet-Type Remcon Relay Switch

$49.95
  • Review
  • TAG : Yay! You're now following relay wiring diagram in your .
ADD TO CART
  • Most relay logic diagrams are in "ladder logic" form. Systems using relay logic diagrams in other forms include the , the many 20th century that controlled their by relays, and the designs for the various including the . Design tools for these include and .

    The most common relays used to control electrical accessory devices in the automotive industry are Mini and Micro relays. 4 and 5 pin designs, SPST / SPDT are used in both styles of automotive relays. Normally open or normally closed types. Look for relay diagrams or a relay schematic that is printed on the side of the relay to determine it's function. 20, 30 and 40 amp relays are common in automotive use. Below are some examples of basic 12 volt car relays.

  • In many cases, it is possible to design a relay logic diagram directly from the narrative description of a control event sequence. In general, the following suggestions apply to designing a relay logic diagram:

    Note:In a basic or resistor protection relay, pins 1 and 2 of the micro relays and pins 85 and 86 of the mini relays can be interchanged positive or negative. In a diode protected relay, Mini relays must be pin 85 (+) power, pin 86 (-) ground / Micro relays must be pin 2 (+) power, pin 1 (-) ground. Look for a relay diagram or a relay schematic that is printed on the side of the relay to determine.

      #1 (permalink)  
    01-01-2011, 01:19 PM
    VICTORY_OR_BUST
    Club Chopper Member

     
    Join Date: Jun 2010
    Location: Belle Plaine, MN
    Bike Year, Make, Engine: 2007 Vic Vegas Custom Pro street
    Posts: 173
    Blog Entries: 1
    Not Ranked     
    4 prong relay diagram

    hey does anyone have relay diagrams for 4 prongs? i'm going from a 4 prong to a five with a moomentary but dont know which slots are what, i looked and serched and could't find anything so i'm hopin you guys have somethin.

    its a about half inch wide by an inch long with 2 prongs runnig paralel vertically and 2 running horizontally paralel

    thanks again guys appreciate it
    __________________
    LIFE'S BEST AT WIDE OPEN

  • One Channel to Multiple Outputs (link)
    You can add multiple functions to an AUX output of an alarm or keyless entry by adding a relay in series with the output wire as shown to any switch or accessory with an output. Only one output can be active at anytime, the one first in the chain (bottom relay in diagram) will have priority, so if you wanted to have the ignition from the key to have priority over the ignition from the remote start, you would connect it to the first relay and the output of the remote start to the next and so on. Also pay attention to the top relay shown. Terminal #87a (the default output) will be active only when none of the coils of the relays are energized. There are many other accessories that can be used with this, including the remote turn on wire and/or power antenna wire of your head unit.
     
     

    Figure 1 shows a typical relay logic diagram. In this circuit, a STOP/START station is used to control two . When the START button is pressed, the control relay energizes and its associated contacts change state. The green pilot light is now ON and the red lamp is OFF. When the STOP button is pressed, the contacts return to their resting state, the red pilot light is ON, and the green switches OFF.

Automotive Relay Diagram - Del City

People use a fuel pump relay diagram to locate the control circuit terminals and the power circuit terminals on a fuel pump relay, as eBay explains. This diagram is typically located on the casing of the fuel pump relay.